Using Plantain Rachis Fibers and Mopa-Mopa Resin to Develop a Fully Biobased Composite Material.

A completely biobased composite material was developed using a matrix of natural resin extracted from the Elaegia pastoensis Mora plant, commonly known as Mopa-Mopa or "Barniz de Pasto", reinforced with fibers extracted from plantain rachis agricultural residues. A solvent process, involving grinding, distillation, filtration, and drying stages, was implemented to extract the resin from the plant bud. To obtain the resin from the plant bud, the vegetable material was ground and then dissolved in a water-alcohol blend, followed by distillation, filtration, and grinding until the powdered resin was ready for use in the preparation of the biocomposite. Likewise, using mechanical techniques, the plantain rachis fibers were extracted and worked in their native condition and with a previous alkalinization surface treatment. Finally, the biocomposite material was developed with and without incorporating stearic acid, which was included to reduce the material's moisture absorption. Ultimately stearic acid was used as an additive to reduce biocomposite moisture absorption. The tensile mechanical results showed that the Mopa-Mopa resin reached a maximum strength of 20 MPa, which decreased with the incorporation of the additive to 12 MPa, indicating its plasticization effect. Likewise, slight decreases in moisture absorption were also evidenced with the incorporation of stearic acid. With the inclusion of rachis plantain fibers in their native state, a reduction in the tensile mechanical properties was found, proportional to the amount added. On the other hand, with the alkalinization treatment of the fibers, the behavior was the opposite, evidencing increases in tensile strength, indicating that the fiber modification improved the interfacial adhesion with the Mopa-Mopa matrix. On the other hand, the evaluation of the moisture absorption of the biocomposite material evidenced, as expected, that the absorption level was favored by the relative humidity used in the conditioning (47, 77, and 97%), which also had an impact on the decrease of the mechanical tensile properties, being this was slightly counteracted by the inclusion of stearic acid in the formulation of the material.

Assessing the Effect of Cellulose Nanocrystal Content on the Biodegradation Kinetics of Multiscale Polylactic Acid Composites under Controlled Thermophilic Composting Conditions.

This work studied the effect of cellulose nanocrystal (NCC) content on the biodegradation kinetics of PLA-based multiscale cellulosic biocomposites (PLAMCBs). To facilitate biodegradation, the materials were subjected to thermo-oxidation before composting. Biodegradation was carried out for 180 days under controlled thermophilic composting conditions according to the ASTM D 5338 standard. A first-order model based on Monod's kinetics under limiting substrate conditions was used to study the effect of cellulose nanocrystal (NCC) content on the biodegradation kinetics of multiscale composite materials. It was found that thermo-oxidation at 70 °C for 160 h increased the biodegradability of PLA. Also, it was found that the incorporation of cellulosic fibrous reinforcements increased the biodegradability of PLA by promoting hydrolysis during the first stage of composting. Likewise, it was found that partial substitution of micro cellulose (MFC) by cellulose nanocrystals (NCCs) increased the biodegradability of the biocomposite. This increase was more evident as the NCC content increased, which was attributed to the fact that the incorporation of cellulose nanocrystals facilitated the entry of water into the material and therefore promoted the hydrolytic degradation of the most recalcitrant fraction of PLA from the bulk and not only by surface erosion.

Tensile Behavior of 3D Printed Polylactic Acid (PLA) Based Composites Reinforced with Natural Fiber.

Natural fiber-reinforced composite (NFRC) filaments for 3D printing were fabricated using polylactic acid (PLA) reinforced with 1-5 wt% henequen flour comprising particles with sizes between 90-250 µm. The flour was obtained from natural henequen fibers. NFRCs and pristine PLA specimens were printed with a 0° raster angle for tension tests. The results showed that the NFRCs' measured density, porosity, and degree of crystallinity increased with flour content. The tensile tests showed that the NFRC Young's modulus was lower than that of the printed pristine PLA. For 1 wt% flour content, the NFRCs' maximum stress and strain to failure were higher than those of the printed PLA, which was attributed to the henequen fibers acting as reinforcement and delaying crack growth. However, for 2 wt% and higher flour contents, the NFRCs' maximum stress was lower than that of the printed PLA. Microscopic characterization after testing showed an increase in voids and defects, with the increase in flour content attributed to particle agglomeration. For 1 wt% flour content, the NFRCs were also printed with raster angles of ±45° and 90° for comparison; the highest tensile properties were obtained with a 0° raster angle. Finally, adding 3 wt% content of maleic anhydride to the NFRC with 1 wt% flour content slightly increased the maximum stress. The results presented herein warrant further research to fully understand the mechanical properties of printed NFRCs made of PLA reinforced with natural henequen fibers.

Effect of Cellulose and Cellulose Nanocrystal Contents on the Biodegradation, under Composting Conditions, of Hierarchical PLA Biocomposites.

In this work, the effect of microfibrillated cellulose (MFC) and cellulose nanocrystals (CNCs) on the biodegradation, under composting conditions, of hierarchical PLA biocomposites (HBCs) was studied using a full 22 factorial experimental design. The HBCs were prepared by extrusion processing and were composted for 180 days. At certain time intervals, the specimens were removed from the compost for their chemical, thermal and morphological characterizations. An ANOVA analysis was carried out at different composting times to study MFC and CNCs' effects on biodegradation. The specimen's mass loss and molecular weight loss were selected as independent variables. The results show that the presence of MFC enhances the PLA biodegradation, while with CNCs it decreases. However, when both cellulosic fibers are present, a synergistic effect was evident-i.e., in the presence of the MFC, the inclusion of the CNCs accelerates the HBCs biodegradation. Analysis of the ANOVA results confirms the relevance of the synergistic role between both cellulosic fibers over the HBC biodegradation under composting conditions. The results also suggest that during the first 90 days of incubation, the hydrolytic PLA degradation prevails, whereas, beyond that, the enzymatic microbial biodegradation dominates. The SEM results show MFC's presence enhances the surface biodeterioration to a greater extent than the CNCs and that their simultaneous presence enhances PLA biodegradation. The SEM results also indicate that the biodegradation process begins from hydrophilic cellulosic fibers and promotes PLA biodegradation.

Potential Uses of Musaceae Wastes: Case of Application in the Development of Bio-Based Composites.

The Musaceae family has significant potential as a source of lignocellulosic fibres and starch from the plant's bunches and pseudostems. These materials, which have traditionally been considered waste, can be used to produce fully bio-based composites to replace petroleum-derived synthetic plastics in some sectors such as packaging, the automotive industry, and implants. The fibres extracted from Musaceae have mechanical, thermal, and physicochemical properties that allow them to compete with other natural fibres such as sisal, henequen, fique, and jute, among others, which are currently used in the preparation of bio-based composites. Despite the potential use of Musaceae residues, there are currently not many records related to bio-based composites' developments using starches, flours, and lignocellulosic fibres from banana and plantain pseudostems. In this sense, the present study focusses on the description of the Musaceae components and the review of experimental reports where both lignocellulosic fibre from banana pseudostem and flour and starch are used with different biodegradable and non-biodegradable matrices, specifying the types of surface modification, the processing techniques used, and the applications achieved.

Mechanical Properties of Natural Fiber Reinforced Foamed Concrete.

The mechanical characterization of plain foamed concrete (PFC) and fiber-reinforced foamed concrete (FRFC) with a density of 700 kg/m3 was performed with compression and tension tests. FRFC was reinforced with the natural fiber henequen (untreated or alkaline-treated) at volume fractions of 0.5%, 1% and 1.5%. Polypropylene fiber reinforcement was also used as a reference. For all FRFCs, the inclusion of the fibers enhanced the compressive and tensile strengths and plastic behavior, which was attributed to the increase of specimen integrity. Under compressive loading, after the peak strength, there was no considerable loss in strength and a plateau-like regime was observed. Under tensile loading, the fibers significantly increased the tensile strength of the FRFCs and prevented a sudden failure of the specimens, which was in contrast to the brittle behavior of the PFC. The tensile behavior enhancement was higher when treated henequen fibers were used, which was attributed to the increase in the fiber-matrix bond produced by the alkaline treatment. The microscopic characterization showed that the inclusion of fibers did not modify the air-void size and its distribution. Higher energy absorption was observed for FRFCs when compared to the PFC, which was attributed to the enhanced toughness and ductility by the fibers. The results presented herein warrant further research of FRFC with natural henequen fibers for engineering applications.

Biocomposites from abaca strands and polypropylene. Part I: Evaluation of the tensile properties.

In this paper, abaca strands were used as reinforcement of polypropylene matrix and their tensile mechanical properties were studied. It was found relevant increments on the tensile properties of the abaca strand-PP composites despite the lack of good adhesion at fiber-matrix interface. Afterwards, it was stated the influence of using maleated polypropylene (MAPP) as compatibilizer to promote the interaction between abaca strands and polypropylene. The intrinsic mechanical properties of the reinforcement were evaluated and used for modeling both the tensile strength and elastic modulus of the composites. For these cases, the compatibility factor for the ultimate tensile strength was deduced from the modified rule of mixtures. Additionally, the experimental fiber orientation coefficient was measured, allowing determining the interfacial shear strengths of the composites and the critical fiber length of the abaca strand reinforcement. The mechanical improvement was compared to that obtained for fiberglass-reinforced PP composites and evaluated under an economical and technical point of view.

Biofilm colonization dynamics and its influence on the corrosion resistance of austenitic UNS S31603 stainless steel exposed to Gulf of Mexico seawater.

Viable bacterial counts, chemical markers, phospholipid fatty acid analysis (PLFA), and Fourier-transformed infrared spectroscopy (FTIR), together with electrochemical methods, were used to study biofilm dynamics and its impact on the corrosion resistance of UNS S31603 stainless steels exposed to the Gulf of Mexico seawater. Biofilms progressively accumulated, peaking on day 20, but finally detached. The extracellular polysaccharide (EPS)/cellular biomass ratio remained low most of the time, but reached its highest level (4.2+/-1.9) also on day 20. Viable bacterial cells reached their highest abundance earlier (approximately 800 CFU/cm2), on day 15. Biofilms were seen covering the stainless steel surfaces heterogeneously and were composed mainly of gram-negative rods, presumably EPS-producing bacteria. Despite the different levels of biofilm biomass and attachment state, field-exposed steel coupons ennobled significantly and showed more active pitting potentials (approximately +500 mVSCE) than on the abiotic control (+650 mVSCE), where no significant ennoblement occurred. These results suggest that the heterogeneous distribution of biofilms, as opposed to the quantity of surface-associated biomass, promotes formation of differential aeration cells, and that this in turn contributes to the ennoblement of these steels.